Research

Simulations of coatings and interfaces

Most of my research is about what happens where a polymer or a small molecule meets a surface. For example, this can be a coating on paper, a monolayer on silica, or a polymer that holds on to graphene. I use all-atom molecular dynamics (MD) when the chemistry matters, and coarse-grained models such as dissipative particle dynamics (DPD) when the structure forms over larger length and time scales. Below, you can find my eight papers. For each paper, I explain the question, what we did, what we found, and my part in the work.

The papers at a glance

the numbers match the map

  1. Coatings on paper-like surfaces
  2. 1How the block ratio shapes a coating2023
  3. 2When a coating closes and when it cracks2023
  4. 3Which chemistry keeps water out under strain2025
  5. Monolayers on silica
  6. 4Short alkylsilane chains, dry and under waterin review
  7. Polymer and graphene
  8. 5Treating graphene so that PLA holds on to it2020
  9. 6How much grafting is too much2021
  10. 7Shape memory with graphene, in MD and in the lab2020
  11. 8Tuning shape memory with surface groups2022

The figures on this page run in your browser. A few of them are small live simulations with the same kind of model as in the paper, and the rest are drawings and charts made from the published numbers. Each caption says which one it is. None of the figures is copied from a paper.

Coatings on paper-like surfaces

doctoral work, Aalto University

Paper and board are made of cellulose and starch, which attract water. For packaging, they need a thin layer that keeps moisture out. Block copolymers can build such a layer on their own, but only if the chains and the recipe are right. In my doctoral work in Maria Sammalkorpi's group, partly together with industry, I studied what "right" means at the molecular level. In papers 1 and 2, we followed the film as it forms, using DPD. In paper 3, we looked at how water gets into the film, using all-atom MD.

1J. Colloid Interface Sci. 640, 809 (2023)open access

Controlling self-assembling co-polymer coatings of hydrophilic polysaccharide substrates via co-polymer block length ratio

A. Scacchi, K. Hasheminejad, S. Javan Nikkhah, M. Sammalkorpi

Question
Amphiphilic di-block copolymers have one block that likes water and one that does not. When they settle from water onto a hydrophilic surface such as cellulose, what kind of coating do they make, and how does the length ratio of the two blocks change it?
What we did
We used DPD simulations with four kinds of beads, which were a starch-like block (A), a hydrophobic styrene and butyl acrylate block (B), a cellulose substrate, and water. Each chain has seven beads, which is about 35 monomers, with A:B ratios of 6:1, 5:2, and 4:3. The bead repulsions came from Flory-Huggins χ parameters that we computed with all-atom MD. The polymer first formed particles in water. Then, we added the substrate and let the coating grow on it, at a series of polymer concentrations.
What we found
At low concentrations, all copolymers stick to the surface as small patches. At 11.25%, all three cover the surface, but the inside of the film depends on the block ratio. With 6:1, the hydrophobic beads stay mixed in, and with 5:2, they start to separate. The nearly symmetric 4:3 gives a clean layered film, with a hydrophilic layer on the substrate, a hydrophobic middle layer, and a hydrophilic top layer.
Why it matters
The hydrophobic middle layer is the part that keeps water out. The block ratio controls this layer, and it can be chosen before anything is made in the lab.
My part
I ran the simulations and did the analysis together with A. Scacchi, and we wrote the first draft together.

2Appl. Surf. Sci. 640, 158324 (2023)open access

Cracking polymer coatings of paper-like surfaces: Control via block co-polymer structure and system composition

K. Hasheminejad, A. Scacchi, S. Javan Nikkhah, M. Sammalkorpi

Question
Real coating recipes are mixtures, for example of a hydrophobic binder and an amphiphilic polymer that helps it spread. Does the copolymer from paper 1 still give a good film when a hydrophobic polymer is added? And what happens with too little or too much copolymer?
What we did
We added a hydrophobic polymer of 19 beads (B19) to the same DPD model. First, we changed the block ratio of the copolymer from 6:1 to 1:6 at a fixed recipe. Then, for the 3:4 copolymer, we mapped the coating structure from 9 to 15% copolymer and from 7 to 15% B19.
What we found
Very asymmetric copolymers leave droplets with B19 in their core. The balanced 4:3 and 3:4 copolymers give a layered coating with B19 in the middle. The map has three regions. At 9% copolymer, the coating stays incomplete. At 10 to 11.25%, it is complete, and more B19 only makes it thicker. From 12.5% on, the extra copolymer pierces the hydrophobic layer with hydrophilic channels, and the coating cracks.
Why it matters
The map gives a composition window to aim for in a real recipe. The trend follows the packing shape of the chains, which is either a cone or a cylinder, so the same idea also works for other amphiphiles.
My part
I planned the study with A. Scacchi and M. Sammalkorpi, ran the simulations and the analysis, and wrote the first draft with A. Scacchi.

3Comput. Mater. Sci. 258, 114046 (2025)open access

Molecular level dependencies of water permeability in di-block copolymer assemblies

K. Hasheminejad, Y. Morais Jaques, A. Lepo, A. Scacchi, M. Sammalkorpi

Question
In DPD, a bead only knows whether it likes water or not. Which chemical details of the hydrophobic block decide how much water gets into the film, especially when the film is stretched?
What we did
We ran all-atom MD (LAMMPS, OPLS-AA, and TIP3P water) of layers of 98 copolymers. Each copolymer had a five-unit starch block and a ten-unit hydrophobic block. We compared four hydrophobic blocks that are used in paper coatings, which were styrene with n-butyl acrylate, styrene with 2-ethylhexyl acrylate, isobutyl methacrylate with n-butyl acrylate, and methyl methacrylate with n-butyl acrylate. Each system ran for 100 ns and was then stretched up to 10% in the plane. We counted the water molecules inside the hydrophobic layer and measured the interface roughness, chain alignment, and chain extension.
What we found
Without stretching, the 2-ethylhexyl acrylate and isobutyl methacrylate films let in the least water, with 0.33 and 0.38 molecules per nm², compared with 1.2 and 1.3 for the other two. When stretched by 10%, only the styrene and 2-ethylhexyl acrylate film still worked well (0.92 per nm²). Its chains kept their alignment, and its interface stayed smooth. In contrast, the isobutyl methacrylate film became rough, and its water count rose more than fivefold, to 2.0 per nm².
Why it matters
The results suggest a recipe for a barrier that survives strain. It needs bulky or branched side groups that fill space, flexible chains that adapt, and side groups that interlock and keep the chains aligned. These trends agree with what is known for styrene-acrylate paper coatings.
My part
I developed the idea together with A. Lepo, A. Scacchi, and M. Sammalkorpi. I planned the study, ran the simulations and the analysis, and wrote the first draft.
Doctoral thesis, Aalto University, 2026

Computational modelling of block copolymer surface coatings at multiple length scales

The thesis combines papers 1 to 3. Together, they give three design rules for a water barrier made with block copolymers.

  1. Chain shape

    Nearly symmetric di-block copolymers form continuous layered films, while very asymmetric ones leave droplets and patches.

  2. Recipe

    The composition has to be inside the window. Too little copolymer leaves gaps, and too much copolymer breaks the hydrophobic layer. Inside the window, more hydrophobic polymer only makes the film thicker.

  3. Chemistry

    For a barrier that survives stretching, the hydrophobic block should have bulky or branched side groups, a flexible backbone, and side groups that interlock.

Limits. The chains in this work were short, closer to surfactants than to long polymers. In DPD, the beads can pass through each other, and the model has water but no air. MD reaches about a hundred nanoseconds and a few nanometers of film, so it can rank chemistries, but it cannot predict the exact water uptake.

Next steps. In the thesis, I proposed umbrella sampling for the free energy of a water molecule entering the film, a real substrate under the MD film, and many-body DPD so that the film can meet air and give contact angles. I also proposed a hard core in DPD so that chains cannot cross, and passing the MD and DPD results to continuum models for stress and long-time transport.

Monolayers on silica

my newest paper, in review

Grafting alkylsilane chains to glass or silicon oxide is one of the simplest ways to change how a surface interacts with water. This paper is in review, so here I show only the question and the methods. I will add the results when the paper is accepted.

4submitted to J. Colloid Interface Sci.in review

Hydration-enhanced chain length effects in short alkyl chain self-assembled monolayers on silica

K. Hasheminejad, D. Tolmachev, M. Sammalkorpi

Question
Short alkylsilane monolayers, with four to eight carbons, are used to control how glass and silicon oxide surfaces interact with water, but the structures reported for them vary a lot. How do chain length, odd or even length, the number of chains per area, and water on top together shape such a layer?
What we did
We ran all-atom MD in GROMACS of chains with four to eight carbons on hydroxylated alpha-quartz, at eleven coverages from 0 to 3.9 chains per nm². The top of this range matches the densest layers made in the lab. Every system was run both dry and under water, for 100 ns each, with the INTERFACE force field for silica, CHARMM36 for the chains, and TIP3P water. I built the systems with my own builder, apadana, and took the parameters of the Si-C bond at the grafting point from quantum chemistry.
What we found
I will add the findings when the paper is accepted.
My part
I developed the concept and the methods, ran the simulations and the analysis, made the figures, and wrote the first draft.

Polymer and graphene

M.Sc. work, K. N. Toosi University of Technology

My M.Sc. work with Abbas Montazeri was about polylactide (PLA), a polyester made from plant sugars, and graphene. Two of the papers ask how to make the two materials hold together, and the other two ask how graphene changes a PLA that remembers its shape. All four papers use all-atom MD, and in paper 7, the simulations are compared with lab tests.

5Appl. Surf. Sci. 502, 144150 (2020)

Enhanced interfacial characteristics in PLA/graphene composites through numerically-designed interface treatment

K. Hasheminejad, A. Montazeri

Question
Graphene can make PLA stiffer and stronger, but only if the load passes across the interface. Which treatment of the graphene surface makes this interface the strongest?
What we did
We ran MD pull-out tests in LAMMPS, in which a graphene sheet is pulled out of PLA. The sheet was either bare, carried hydroxyl, carboxyl, methyl, or amine groups, or had PLA chains grafted to it at five densities. We first checked the PLA model against its measured density, glass transition, and stiffness.
What we found
Bare graphene gives an interfacial shear strength of about 110 MPa. Carboxyl groups at 5% coverage raise it about fivefold (+405%). Grafted PLA chains at the best density, 0.0072 per Ų, do slightly better (+410%), and they raise the fracture toughness by 271%. Above this density, there is no further gain. In contrast, more hydroxyl groups help steadily up to 10% coverage.
Why it matters
The simulations rank the treatments before anything is synthesized. Grafting chains of the matrix polymer itself comes out on top.
My part
This paper came from my M.Sc. work, supervised by A. Montazeri, and I am the first author.

6Eur. Polym. J. 148, 110351 (2021)

Tailoring adhesion characteristics of poly(L-lactic acid)/graphene nanocomposites by end-grafted polymer chains: An atomic-level study

K. Hasheminejad, A. Montazeri, H. Hasheminejad

Question
A pull-out test shears the interface. However, the polymer is often pulled straight off the filler instead. How does grafting change this, and how much grafting is best?
What we did
We ran MD pull-off tests of poly(L-lactic acid) (PLLA) on graphene with end-grafted PLLA chains of six monomers, at 0.002 to 0.008 chains per Ų. At 0.004 chains per Ų, we also compared chains standing up (a brush) with chains lying flat (a mushroom), and we tested chains of 3 and 12 monomers.
What we found
Light grafting works best. At 0.002 chains per Ų, the normal strength rises from 421.5 to 484.8 MPa, and the interaction energy rises by 14%. Here, the polymer tears before the interface lets go. From 0.006 on, the interface itself becomes the weak spot. The work of adhesion falls by about 40%, and the sheet comes off cleanly. A brush beat a mushroom by 90%, but a very dense brush (0.016) was 58% worse than bare graphene. Both shorter and longer chains beat the 6-mers, but for different reasons. Short chains let the sheet touch the polymer, and long chains entangle further out.
Why it matters
More grafting is not always better. There is an optimum, and the place where the sample breaks shows which side of the optimum you are on.
My part
I did the concept, methods, simulations, analysis, and figures, and I wrote the first draft.

7Composites Part A 138, 106055 (2020)

Experimentally guided MD simulation to enhance the shape memory behavior of polymer-based nanocomposites: Towards elaborating the underlying mechanism

M. Amini, K. Hasheminejad, A. Montazeri

Question
A shape memory polymer can be stretched when warm, fixed in that shape by cooling, and later spring back when heated. Graphene changes how well PDLLA, a form of PLA, does this. Why does this happen, and can MD reproduce what is measured in the lab?
What we did
We measured the same shape memory cycle in the lab, with dynamic mechanical analysis, and ran it in MD, for PDLLA with 0 to 5 wt% graphene. In MD, we also made samples where the sheets clump together.
What we found
The MD matches the measured shape fixity within two percentage points at every loading (92 to 100%). It also follows the measured drop in recovery, from about 80% at 1 wt% to 50 to 60% at 3 and 5 wt%. Clumped sheets lower the recovery further, to 40 and 32%. The recovery is driven by the entropy of the polymer chains, and the sheets get in their way.
Why it matters
A model that is checked against the lab can explain the mechanism and screen fillers before they are made. Paper 8 builds on this model.
My part
Together with M. Amini, I worked on the methods, simulations, validation, analysis, and figures, and we wrote the first draft.

8Smart Mater. Struct. 31, 025010 (2022)

Engineering the shape memory parameters of graphene/polymer nanocomposites through atomistic simulations: On the effect of nanofiller surface treatment

M. Amini, K. Hasheminejad, A. Montazeri

Question
If graphene lowers the recovery, can a treatment of its surface bring the recovery back, or tune it on purpose?
What we did
We ran the MD cycle from paper 7 for PDLLA with 1 wt% graphene. The graphene carried hydroxyl, methyl, or amine groups, or PDLLA chains grafted at three densities.
What we found
Every treatment raises the fixity, from 93% up to 100%. However, only hydroxyl groups also keep the recovery high (84%). Methyl and amine groups lower it to 72 and 69%, and dense grafting lowers it to 39%. The grafted sample also takes almost four times longer to recover the same strain.
Why it matters
The surface treatment can tune the material between one that holds its new shape and one that springs back.
My part
I am the second author, and this work builds on the model from paper 7.

All papers

newest first

    You can also find my papers on Google Scholar and ORCID.

    Talks and posters

    4 talks, 2 posters

    Research-related code

    public on GitHub